請問排氣管生鏽怎麼辦 - 機車討論
By Caroline
at 2009-02-03T01:58
at 2009-02-03T01:58
Table of Contents
我的車車排氣管生鏽
而且很嚴重耶
我用不鏽鋼油膏去擦阿
都擦不掉
有什麼辦法嗎
而且很嚴重耶
我用不鏽鋼油膏去擦阿
都擦不掉
有什麼辦法嗎
Tags:
機車
All Comments
By Wallis
at 2009-02-06T11:50
at 2009-02-06T11:50
不用擦了會越擦越糟
請問你是那一種管?
By William
at 2009-02-09T21:42
at 2009-02-09T21:42
不曉得你說的生鏽很嚴重是多嚴重,
如果沒有繡穿的話,是可以嘗試用砂紙磨,
一般都適用#600~#1000去磨,
磨過之後再視情況用白鐵膏或是你說的不銹鋼油膏推,
如果是黑管就比較簡單,
如果是白鐵的話就較麻煩了,要比較注意砂紙的番數及事後的拋光..
參考囉!
By Hamiltion
at 2009-02-13T07:34
at 2009-02-13T07:34
聽說有隔熱漆..名子我忘了
可以暫時先撐ㄧ下
By Poppy
at 2009-02-16T17:27
at 2009-02-16T17:27
By Selena
at 2009-02-20T03:19
at 2009-02-20T03:19
只是事後的拋光工程,會讓人搞到手軟,罵髒話。
不然送去噴沙,只是工錢大概可以買一隻全新的管了。
By Freda
at 2009-02-23T13:11
at 2009-02-23T13:11
除繡效果還算不錯
By Thomas
at 2009-02-26T23:04
at 2009-02-26T23:04
除非本來操很貴的管
不然再怎麼保養還是都難逃生鏽的下場
By Candice
at 2009-03-02T08:56
at 2009-03-02T08:56
而且順便改車= =
By Dorothy
at 2009-03-05T18:48
at 2009-03-05T18:48
不然拔起來磨掉之後再用耐熱漆噴一噴
修復起來會比較完整
By Yuri
at 2009-03-09T04:41
at 2009-03-09T04:41
By Kelly
at 2009-03-12T14:33
at 2009-03-12T14:33
By Vanessa
at 2009-03-16T00:25
at 2009-03-16T00:25
By Margaret
at 2009-03-19T10:17
at 2009-03-19T10:17
白鐵管可以用拋光的
By Oliver
at 2009-03-22T20:10
at 2009-03-22T20:10
或是用鐵刷刷也可以
一定要把鐵鏽徹底刷乾淨
再上耐熱漆
隔段時間再噴第二層
等乾的時間可以拿噴燈加熱增加附著力
噴個兩三層就可以撐很久了
By Olive
at 2009-03-26T06:02
at 2009-03-26T06:02
再用耐熱漆噴過就像新的一樣拉
By Ivy
at 2009-03-29T15:54
at 2009-03-29T15:54
新的不來
是這樣說嘛!
By Ophelia
at 2009-04-02T01:47
at 2009-04-02T01:47
買砂紙把他磨一磨
然後買鐵樂士黑色的 在上色
上色等他乾 上個兩、三次
就跟新的一樣了...
別拿太進噴阿 有點技巧 不然會 留鼻涕 會不好看噢
By Dora
at 2009-04-05T11:39
at 2009-04-05T11:39
By Connor
at 2009-04-08T21:31
at 2009-04-08T21:31
二、先用鐵刷、砂紙磨平生鏽的地方再噴耐熱漆
By Elizabeth
at 2009-04-12T07:24
at 2009-04-12T07:24
再用砂紙打磨!!
最後再用WD40在噴一次!!
等他吸油每天都噴他就會好了!!
會生銹都是平常不保養!!
By Zora
at 2009-04-15T17:16
at 2009-04-15T17:16
By Elma
at 2009-04-19T03:08
at 2009-04-19T03:08
真要說方法的話
就是不要下雨天騎車
車停室內
下雨天就用走路吧
這樣管子就比較不會生鏽啦
By Genevieve
at 2009-04-22T13:00
at 2009-04-22T13:00
用砂紙從粗(小號)開始磨,把排氣管上的鏽磨掉
從粗砂紙換到細砂紙
不要用到超過1000號,因為等一下要噴耐漆,表面要粗糙一點
漆才咬得住。
鏽都磨乾淨以後用濕布擦乾淨,稍微放著乾燥
然後用耐熱漆來回噴兩~三層
每層不要噴太厚 噴一層等30分鐘再噴下一層
噴完以後靜置一~兩天
有太陽的話曬太陽只要一天就可以了 沒太陽的話放兩天
就完成除鏽跟防鏽了
By Bennie
at 2009-04-25T22:53
at 2009-04-25T22:53
就跟新的一樣了
By Hardy
at 2009-04-29T08:45
at 2009-04-29T08:45
By Puput
at 2009-05-02T18:37
at 2009-05-02T18:37
By Oscar
at 2009-05-06T04:30
at 2009-05-06T04:30
除非你很愛你的車不然生鏽是很正常的
By Sierra Rose
at 2009-05-09T14:22
at 2009-05-09T14:22
By George
at 2009-05-13T00:14
at 2009-05-13T00:14
是原廠管我看是外層的黑色保護漆掉了
By Ula
at 2009-05-16T10:07
at 2009-05-16T10:07
By Ina
at 2009-05-19T19:59
at 2009-05-19T19:59
By Anthony
at 2009-05-23T05:51
at 2009-05-23T05:51
會不會有點....(浪費)
生鏽應該還可以騎吧 = =
用砂摩紙磨一摩吧
By Elma
at 2009-05-26T15:43
at 2009-05-26T15:43
噴漆一下就好了
假如你的管 變薄了 就只好換過了
因為再用一段時間 就會破洞了
By Gary
at 2009-05-30T01:36
at 2009-05-30T01:36
By Ula
at 2009-06-02T11:28
at 2009-06-02T11:28
By Charlotte
at 2009-06-05T21:20
at 2009-06-05T21:20
真的會把那黑黑黃黃的東西磨掉...
但是撐不久就是了...
By Kyle
at 2009-06-09T07:13
at 2009-06-09T07:13
看了各位大大說明
雖然生鏽可以磨掉但也是撐不久
還是換新的比較快
By Lucy
at 2009-06-12T17:05
at 2009-06-12T17:05
可以考慮換心@!!!
By Joseph
at 2009-06-16T02:57
at 2009-06-16T02:57
八耐的被我模到一直開花...虐待到現在切到剩下原來的一半還要短一點...他還是沒生鏽阿
By Isabella
at 2009-06-19T12:50
at 2009-06-19T12:50
換一支 比較快
By Caitlin
at 2009-06-22T22:42
at 2009-06-22T22:42
那就換了吧
By Yuri
at 2009-06-26T08:34
at 2009-06-26T08:34
不用擦了會越擦越糟
請問你是那一種管?
By Skylar DavisLinda
at 2009-06-29T18:26
at 2009-06-29T18:26
By Susan
at 2009-07-03T04:19
at 2009-07-03T04:19
但是可以延長使用時間~
使用鋼刷或沙紙去繡之後洗乾淨使用耐熱漆~
By Gary
at 2009-07-06T14:11
at 2009-07-06T14:11
如果真的很在意就換掉吧
By Ophelia
at 2009-07-10T00:03
at 2009-07-10T00:03
鏽要先處理乾淨~~~就如同樓上大大的做法
先用砂紙磨過~~~然後拋光處理~~~用意是把被鏽腐蝕掉的凹槽補平
之後去機車材料店購買"恐龍牌高溫耐熱漆"來噴
可是要先說的是.......如果版大平常都把車放在戶外任他風吹日曬雨淋的話
這樣的處理方式 大約只能撐一個月多
他就會從原本的焊接處再次生鏽
有點麻煩就是了 還是建議 換新的比較省功!!!
By Eden
at 2009-07-13T09:56
at 2009-07-13T09:56
白鐵其實也會生銹 你只要拿一張 用過爛爛的菜瓜布 慢慢畫圓 擦他 很快就會把繡擦掉
不過 如果是 黑色的我想你換一根會比較快唷!
By Rosalind
at 2009-07-16T19:48
at 2009-07-16T19:48
再去買一瓶恐龍牌的耐熱漆 記得 磨完的排氣管要趕快晾乾
等乾了之後 就拿鐵絲吊起來噴 記得離30公分左右
由上往下 不要只噴一個點 噴完一圈之後 等數分鐘 在噴依次 可多噴2~3次
大功告成 放一個晚上給他乾 然後就可以裝上車囉
By Ingrid
at 2009-07-20T05:40
at 2009-07-20T05:40
不然就是上一層漆吧!!
By Hardy
at 2009-07-23T15:33
at 2009-07-23T15:33
然後再拿耐熱漆噴就行啦!…
和新的一樣唷…不過還是會有生鏽的問題…
By Iris
at 2009-07-27T01:25
at 2009-07-27T01:25
By Puput
at 2009-07-30T11:17
at 2009-07-30T11:17
By Zora
at 2009-08-02T21:09
at 2009-08-02T21:09
改裝就丟了
改裝不值錢
很喜歡他 去機車場哪廢棄機有 給他微微的噴上
By Hedwig
at 2009-08-06T07:02
at 2009-08-06T07:02
By Eartha
at 2009-08-09T16:54
at 2009-08-09T16:54
就用鐵刷或是弗蘭達
把鐵銹磨掉
記得阿
要噴上耐高溫的黑漆
不然一樣會生鏽!!
By Hardy
at 2009-08-13T02:46
at 2009-08-13T02:46
如果以經用很久的話就建議可以去換新的了
去改裝店逛逛看看
By Poppy
at 2009-08-16T12:39
at 2009-08-16T12:39
只是事後的拋光工程,會讓人搞到手軟,罵髒話。
不然送去噴沙,只是工錢大概可以買一隻全新的管了
By Kelly
at 2009-08-19T22:31
at 2009-08-19T22:31
之後上個耐熱七還可以檔一震子
By Robert
at 2009-08-23T08:23
at 2009-08-23T08:23
大部分改裝行都有提供這種服務 也不過500有找
如果是原廠排氣管 那就換支付廠吧!!
By Tristan Cohan
at 2009-08-26T18:16
at 2009-08-26T18:16
如果很嚴重應該也魔不掉了
By Tristan Cohan
at 2009-08-30T04:08
at 2009-08-30T04:08
除非本來操很貴的管
不然再怎麼保養還是都難逃生鏽的下場
By Sandy
at 2009-09-02T14:00
at 2009-09-02T14:00
By Sandy
at 2009-09-05T23:52
at 2009-09-05T23:52
By Isla
at 2009-09-09T09:45
at 2009-09-09T09:45
然後用砂紙把排氣管磨一磨
特別是生鏽的地方
然後用高溫的噴漆再噴一噴
By Franklin
at 2009-09-12T19:37
at 2009-09-12T19:37
在用隔熱漆
Related Posts
YAMAHA GTR-areo VS SHOEI X-11
By Ina
at 2009-02-02T22:31
at 2009-02-02T22:31
義興機車行
By Ivy
at 2009-02-02T22:29
at 2009-02-02T22:29
小眼睛機車工作室
By Linda
at 2009-02-02T21:53
at 2009-02-02T21:53
小眼睛機車工作室
By Christine
at 2009-02-02T18:34
at 2009-02-02T18:34
警察搶錢一拜.. .. 超速你說了算?
By Skylar Davis
at 2009-02-02T13:58
at 2009-02-02T13:58