DIY握把套貼皮 - 機車
By Quanna
at 2022-01-11T09:48
at 2022-01-11T09:48
Table of Contents
雖然車才剛滿一年,但是握把橡膠握起來有些黏黏的,清洗過也一樣。
看了很多款握把套都沒看到中意的,而且換套還要氣槍輔助,想說乾脆
直接貼層皮上去,快弄好才發現前面步驟忘了拍照。
步驟一,先量握把圓徑跟長度,長度我直接忽視左右突出的地方只量中
間直的部分,畢竟要貼皮而已,不要增加難度。
步驟二,裁皮,本身有在小玩皮製品,所以有現成的皮可用,我是使用
原色植鞣皮,厚度1.6mm,依照步驟一量的長寬裁左右兩片。
步驟三,紋路,本來是打算用菱格紋,但是單純菱格紋好像不能凸顯個
人化,所以讓線條歪斜點。照理菱格紋應該要有縫線,但我懶
得手縫,機縫又怕車歪,所以最後決定用打印工具打線槽。
步驟四,上色,顏色使用焦糖棕色皮革的水性染料,乾了再上一次反覆
上三次,但我塗完覺得顏色有些紅紅的,最後再上層保護漆。
步驟五,貼皮,本來要用強力膠直接貼上去,但又怕脫落,所以還是用
對縫的方式縫合,讓縫線藏在下方,正常對縫應該要平貼,但
我只有直針沒勾針,只好讓它凸起一小塊。是說這一小塊在轉
油門剛好可以用大拇指來輔助轉動。
http://i.imgur.com/2nDcuU2.jpg
http://i.imgur.com/Qoeyy6c.jpg
最後完成的握起來的感覺很滿意,而且也好看
http://i.imgur.com/xlfuAX9.jpg
http://i.imgur.com/csj9kuM.jpg
http://i.imgur.com/xPEQy49.jpg
--
Tags:
機車
All Comments
By Faithe
at 2022-01-08T21:33
at 2022-01-08T21:33
By Faithe
at 2022-01-13T15:24
at 2022-01-13T15:24
By Noah
at 2022-01-08T21:33
at 2022-01-08T21:33
By Bennie
at 2022-01-13T15:24
at 2022-01-13T15:24
By Jessica
at 2022-01-08T21:33
at 2022-01-08T21:33
By Noah
at 2022-01-13T15:24
at 2022-01-13T15:24
By Ina
at 2022-01-08T21:33
at 2022-01-08T21:33
By Regina
at 2022-01-13T15:24
at 2022-01-13T15:24
By Carol
at 2022-01-08T21:33
at 2022-01-08T21:33
By Joe
at 2022-01-13T15:24
at 2022-01-13T15:24
By Kyle
at 2022-01-08T21:33
at 2022-01-08T21:33
By Anthony
at 2022-01-13T15:24
at 2022-01-13T15:24
By Oliver
at 2022-01-08T21:33
at 2022-01-08T21:33
By Anthony
at 2022-01-13T15:24
at 2022-01-13T15:24
By Sierra Rose
at 2022-01-08T21:33
at 2022-01-08T21:33
By Elvira
at 2022-01-13T15:24
at 2022-01-13T15:24
By Carol
at 2022-01-08T21:33
at 2022-01-08T21:33
By Kristin
at 2022-01-13T15:24
at 2022-01-13T15:24
Related Posts
機車待轉區真的可以廢了
By Barb Cronin
at 2022-01-10T23:29
at 2022-01-10T23:29
不爽送修機車3個月還沒好 男竟夥同友人
By Lauren
at 2022-01-10T22:13
at 2022-01-10T22:13
野狼R150空濾外部進氣的位置?
By John
at 2022-01-10T18:34
at 2022-01-10T18:34
台北市可自備胎皮的店家
By James
at 2022-01-10T17:04
at 2022-01-10T17:04
後避震內管要上油嗎
By Quintina
at 2022-01-10T16:47
at 2022-01-10T16:47