自行維修，千斤頂or駐車架？ - 重機
By Agatha
at 2021-04-21T09:03
at 2021-04-21T09:03
Table of Contents
各位板友好，我的車是Suzuki SFV650。原本要分享換上brembo來令的使用心得。但上上禮拜發現右前叉漏油了（變超級軟），想說先把這個問題解決再來試，上禮拜已經先用野狼練習換過前叉油了（拆下分解、清洗、加入新前叉油、新油封），應該沒什麼太大的問題。因為換前叉需把前輪撐起，所以有個問題想請教各位。
我目前是有想到2個方法來維修：
1. 後駐車架+三角台駐車架
2. 後駐車架+千斤頂
第1個方法我是怕三角台駐車架立起來後，會佔掉一些空間怕拆裝不易。我比較傾向第2個方法，但受限於車型可能要直接頂在排氣管下，不知到會不會造成什麼不良影響（排氣管變形等）？
感謝各位板友！
-----
Sent from JPTT on my LGE LM-V510N.
--
Tags:
重機
All Comments
By James
at 2021-04-22T02:19
at 2021-04-22T02:19
By Emily
at 2021-04-22T14:54
at 2021-04-22T14:54
By James
at 2021-04-27T08:09
at 2021-04-27T08:09
By Carol
at 2021-04-28T05:15
at 2021-04-28T05:15
還是要有機械結構支撐
By Olivia
at 2021-04-30T15:34
at 2021-04-30T15:34
能會凹
By John
at 2021-05-04T16:34
at 2021-05-04T16:34
的吧 千斤頂沒地方能直接頂車台或是底殼
By Eartha
at 2021-05-09T14:30
at 2021-05-09T14:30
By Bethany
at 2021-05-13T17:07
at 2021-05-13T17:07
By Liam
at 2021-05-13T22:36
at 2021-05-13T22:36
By Madame
at 2021-05-14T00:17
at 2021-05-14T00:17
By John
at 2021-05-18T20:19
at 2021-05-18T20:19
參考看看 RC390 用三角台柱車架，施工空間還滿大的~
By Dinah
at 2021-05-23T09:26
at 2021-05-23T09:26
固定前部換前叉油
By Lydia
at 2021-05-26T13:55
at 2021-05-26T13:55
千斤頂是要拆到後搖臂才需要吧,而且要找車架荷重點
By Eden
at 2021-05-29T19:21
at 2021-05-29T19:21
By Quanna
at 2021-06-02T05:39
at 2021-06-02T05:39
By Olga
at 2021-06-05T23:00
at 2021-06-05T23:00
By Iris
at 2021-06-06T14:13
at 2021-06-06T14:13
By Tracy
at 2021-06-08T21:31
at 2021-06-08T21:31
By Harry
at 2021-06-11T05:13
at 2021-06-11T05:13
By Valerie
at 2021-06-11T07:15
at 2021-06-11T07:15
Related Posts
新手入門選擇
By Quintina
at 2021-04-20T20:50
at 2021-04-20T20:50
新手入門選擇
By Kumar
at 2021-04-20T08:35
at 2021-04-20T08:35
新手入門選擇
By Dora
at 2021-04-20T08:22
at 2021-04-20T08:22
關渡大台北重機駕訓班
By Skylar DavisLinda
at 2021-04-20T08:11
at 2021-04-20T08:11
鶯歌地區有可以寄重機的地方嗎？
By Anonymous
at 2021-04-20T08:06
at 2021-04-20T08:06